Switching to Mono-PE: What Changes on the Line

Switching to Mono-PE: What Changes on the Line

Seal window, stiffness, line speed and drop performance — the four things that change when a laminate becomes a recyclable mono-material pack.

2026-11-17 · SUNOVO

The decision to move a pack to mono-PE is usually taken by a brand team and delivered to a production team. That handover is where most switches lose a quarter: the material works, but the line was set up for something else.

The seal window narrows

PE seals at a lower temperature than the seal layer on a PET//AL//PE laminate, and the window between "not sealed" and "sealed through" is narrower. On an older machine with coarse temperature control, that window can be the whole problem. The fix is usually a machine adjustment — better jaw temperature control, a shorter dwell — not a different film.

Stiffness falls

A mono-PE structure is softer than a foil laminate of the same thickness. On a vertical form-fill-seal machine that means the film behaves differently over the forming shoulder: it drapes rather than slides, and the seal at the back of the tube can wrinkle. Machine settings and, sometimes, a slightly heavier gauge solve it.

Line speed drops, at least at first

Lower stiffness and a narrower seal window usually mean a slower line until the settings are optimised. A realistic plan assumes 10–20% slower for the first production runs, and does not promise the buyer that speed will be unchanged.

Drop and puncture performance need re-testing

Mono-PE at the same thickness is generally less puncture-resistant than a PET-containing laminate. For a large pet food bag this matters: the drop test has to be repeated on the new structure, at the new thickness, with the actual product inside.

Barrier is the honest conversation

MDO-PE, EVOH and coatings get mono-PE structures to a real barrier — but usually not to the barrier of the foil laminate they replace. The question to answer before the switch is what shelf life the product actually needs, not what the old pack delivered.

A workable sequence

  1. Define the barrier and shelf life the product genuinely requires.
  2. Select two candidate mono structures and test both on the line.
  3. Re-run the drop and seal-strength tests on the finished pack.
  4. Run a market trial before the national switch.
  5. Only then commit the print cylinders to the new repeat.

Brands that skip step two spend the next year explaining why the pack leaks.

The cylinder and cost consequences

A material switch usually arrives with a print change, because the new structure needs a new repeat and often a new panel layout. That means new cylinders, which is the largest single cost in the project and the reason switches are planned around print renewal cycles.

The material cost per square metre may rise or fall depending on the gauge needed to hit the barrier and puncture targets. A mono-PE structure that has to match a foil laminate's performance often needs more thickness, and the saving in material cost can disappear once the gauge is increased.

Budget the project as: cylinders plus trial material plus line time plus the cost of running a market trial. The film is rarely the biggest line.

A realistic timeline

  1. Weeks 1–2. Define shelf life and barrier requirement; shortlist two structures.
  2. Weeks 3–6. Trial rolls, line trials on both structures, seal-window mapping.
  3. Weeks 6–8. Drop, puncture and seal-strength testing on finished packs; accelerated shelf-life if the barrier is new.
  4. Weeks 8–14. Market trial in one region; retailer conversations about the claim.
  5. Weeks 14–20. Print cylinders, artwork approval, production switch.

Compressing this below about four months is possible only when the structure is already proven on a similar product.

What to tell the retailer

Retailers increasingly ask for recyclability evidence rather than a logo. What they usually want is the material composition, the collection stream the pack is designed for, and the supporting test data. A claim that cannot be traced to a composition and a stream is the one that gets challenged.

It is also worth agreeing upfront how the pack will be described on shelf: "recyclable where facilities exist" is defensible; "100% recyclable" is not, unless the whole pack — including the zipper, the valve and any label — goes into the same stream.

Where the switch usually stalls

Most stalled mono-PE projects stall at the same point: the barrier target and the recyclability claim cannot both be met at the current gauge, and nobody wants to be the one who proposes a shorter shelf life. The way through is to separate the two decisions — agree the shelf life the product genuinely needs, then design the simplest structure that meets it, rather than starting from the old laminate and subtracting layers.

Starting from the requirement instead of the incumbent pack is the single change that makes these projects finish.

It also helps to decide early whether the recyclable pack is a range-wide switch or a single SKU pilot. A pilot produces the line data the rest of the range needs, at a fraction of the cylinder cost, and it gives the sales team a story to test before the national launch.

Applying this to a live pack?

Send the structure and the fill; the answer comes back with a proposed laminate.

Ask a question